PERHITUNGAN VOLUME BATUAN MENGGUNAKAN SOFTWARE AUTOCAD CIVIL 3D DENGAN METODE RULE OF GRADUAL CHANGE DAN RULE OF NEAREST POINT

Authors

  • Jarwanto Jarwanto Universitas Akprind Indonesia
  • Arie Noor Rakhman Universitas Akprind Indonesia
  • Himawan Rico Sanjaya Universitas Akprind Indonesia

DOI:

https://doi.org/10.59003/nhj.v4i8.1322

Keywords:

Tuff, lapili, Autocad Civil 3D, cut, volume

Abstract

The research was conducted in an area located in Segoroyoso, Kapanewon Pleret, Bantul Regency, Yogyakarta Special Region Province. The enclosing rocks are part of the Semilir Formation in the form of tuff interspersed with lapilli. The rock located on this cliff will be cut with a length of 83 meters and a height of 36 meters with the aim of making a flat horizontal plane with an elevation of 50 meters above sea level which will then be made into building construction for the purposes of erecting boarding school buildings. The calculation of rock volume is based on Autocad Civil 3D software with the emphasis on 2 calculation methods, namely calculations using the Rule of Gradual Change and getting a volume of 106,714 m3 and according to the Rule of Nearest Point method getting a volume of 106,495 m3. There is a difference in the calculation results but the difference is not far adrift.

Downloads

Download data is not yet available.

References

Amin A, (2020), Estimasi Sumberdaya Batugamping Menggunakan Metode Penampang Tegak. p ISSN, 1:2622-4267

Putra D, (2016), Estimasi Sumberdaya Pasir Batu Dengan Metode Cross Section Dan Metode Contour Pada Kecamatan Bantarbolang Kabupaten Pemalang Provinsi Jawa Tengah, Skripsi Jurusan Teknik Pertambangan UPN Yogyakarta

Sihombing C, (2018), Estimasi Sumberdaya Batugamping Menggunakan Metode Sayatan Di PT. Sugih Alamanogroho Kab. Gunungkidul, D.I.Y, Tesis Jurusan Teknik Pertambangan Universitas Nasional “Veteran” Yogyakarta.

Sudarto Dkk, (2005), Diktat Mata Kuliah Metode Perhitungan Cadangan, Institut Teknologi Bandung.

Sukandarrumidi, 2009, Bahan galian Industri, Yogyakarta, Gadjah Mada University Press.

Downloads

Published

2025-01-10

How to Cite

Jarwanto, J., Arie Noor Rakhman, & Himawan Rico Sanjaya. (2025). PERHITUNGAN VOLUME BATUAN MENGGUNAKAN SOFTWARE AUTOCAD CIVIL 3D DENGAN METODE RULE OF GRADUAL CHANGE DAN RULE OF NEAREST POINT. Nusantara Hasana Journal, 4(8), 152–159. https://doi.org/10.59003/nhj.v4i8.1322

Issue

Vol. 4 No. 8 (2025): Nusantara Hasana Journal, January 2025

Section

Articles

License

Copyright (c) 2025 Jarwanto

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

NHJ is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Articles in this journal are Open Access articles published under the Creative Commons CC BY-NC-SA License  This license permits use, distribution and reproduction in any medium for non-commercial purposes only, provided the original work and source is properly cited.
Any derivative of the original must be distributed under the same license as the original.